Dillon FI-90 Force IndicatorUsers Manual
10For the standard AC version (See Figure 2): Plug the power cord into theback of the indicator and connect the cord with an external AC power source.
111. Power up the indicator. . . The FI-90 powers up in the samemode it was in when power wasremoved.2. Access the gross mode. If thegross annunciator
12Entering or Viewing an ID Number4. View and, if necessary, record theretained peak value. PressPRINT / SELECT to transmit datato a peripheral device
133. You now have two choices, A or B:A. Accept the displayed ID bypressing either GROSS /PEAK or PRINT / SELECT. . . GROSS / PEAK takes you directlyo
142. Start with the left-most digit (inour example, a 6 ). Pressing UPARROW one depression for eachwhole number, increment thedisplayed number up to t
15A setpoint cutoff is a force-load value at which an internal electrical connec-tion is broken, causing an external relay to de-energize. Additional
162. Enter a new setpoint value inregister #0, using the procedurepresented in the section, EnteringData with Arrow Keys. Before youenter any numeric
17The cutoff connector located on the bottom of the indicator is a nine-pinfemale connector. Figure 7 shows the pin assignments.Signal Name Pin Numbe
183. After the clock is set, you maypress PRINT / SELECT to startthe clock and return to operationsmode menu,. . . Hour is displayed and the clockbegi
19RS-232PinSignal Name NumberTransmit to printer #3Receive from printer #2CTS (BUSY) from printer #8DTR (READY) to printer #4Logic ground #5Shield #9Y
2CAUTION12/19/03 FI90_U.P65 PN 29527-0011E e2 Printed in USARisk of electrical shock. Do not remove cover. No user service-able parts inside. Re
20An optional, isolated analog output provides dip-switch selectable output: 1-5mA, 4-20mA, 10-50mA, 0-5VDC, 0-10VDC. The analog output can be usedwit
21Test mode allows you to test various functions of the FI-90. A flowchart of thetest mode menu is shown in Figure 11, followed by instructions for ge
22VERSION version - Under version are the Weigh-Tronix part number forthe FI-90 force indicator, and the revision number forthe software found in your
23
DillonA division of Weigh-Tronix Inc.1000 Armstrong Dr.Fairmont, MN 56031 USATelephone: 507-238-4461Facsimile: 507-238-8258e-mail: dillon@weigh-troni
3Table of Contents ... 3FI-90 Specifications ...
4FI-90 SpecificationsDisplay: 7-segment LCD, 6-1/2 digits plus sign, .5 inch high, movable decimal, with7 annunciatorsDisplay Update Rate: Two times p
5Automatic Zero Tracking: Window programmable from 0 to 999999 divisions; decimal entries accepted.Tracking in peak-view mode may be enabled or disabl
6Features and OptionsStandard AC VersionOptions: RS232 / 20mA current loop serial I/O with real-time clockDual cutoffs with one programmable inputAnal
7IntroductionThe FI-90, a full-function force indicator, is available in four versions:1) the standard AC powered version2) an AC lead-acid, rechargea
8ONGross Illuminates when the indicator is in gross mode.Peak Illuminates when the indicator is in peak-view mode.lb, kg, N Illuminates to show the ac
9Powering UpFigure 2Back Panel of Standard AC-Powered VersionFigure 5Back Panel of Twelve-Volt-DC VersionFigure 3:Back Panel of AC / Lead-Acid, Rec
Comments to this Manuals